Bean Bag Frags Display And System Build

[unibob]

I am running a waveline dc12000 and have it dialled back to just under 50%
It moves a lot of water, considering I have it pumping my returns and a manifold with outputs for 2 reactors and another return to my fuge.
It is also able to pump water up through my ceiling and across my home for water changes no problem.

My only issue is that it is not dead quiet like I had expected. There is a slight whining noise that is obvious when its running.
It does blend in with the hum of my vortechs, so its not too bad.

Make sure you get the new larger heat sink, I think all gen2 models should have it. Huge improvement over the first gen that were cooled with the small cpu fan.

How many feet of pipe do you have it pumping through? And how high is that water being pumped.


Sent from my iPhone using Tapatalk

 

[teebone110]

How many feet of pipe do you have it pumping through? And how high is that water being pumped.


Sent from my iPhone using Tapatalk

If your referring to my water change system, it goes about 8 feet up and 75 feet across the ceiling through one inch flex pvc to the other side of my basement, so about 85 feet total lol

 

[unibob]

If your referring to my water change system, it goes about 8 feet up and 75 feet across the ceiling through one inch flex pvc to the other side of my basement, so about 85 feet total lol

Ok, I should be fine then. I have max 5 feet up 10 feet over.

Will be running four 1" spaflex returns, manifold with capability of handling 3 reactors.




Sent from my iPhone using Tapatalk

 

[teebone110]

E-Z P-Z
Should be no problem

 

[unibob]

The water flows. Adding rodi to fragtank side. Will add display into system once all plumbing arrives this week.

Sent from my iPhone using Tapatalk

 

[reef keeper]

You go! Woohoo

 

[heath]

looking good, its always exciting when the water goes in,,,

 

[AdInfinitum]

Very nice Jerry...it's all coming together!!!

 

[Petercar (RIP Dec 2017)]

I have got the big new heat sink controller. They send it free on warranty. The fan was making noise so they just send a whole new controller I have the 10,000


Sent from my iPad using Tapatalk HD

 

[teebone110]

I have got the big new heat sink controller. They send it free on warranty. The fan was making noise so they just send a whole new controller I have the 10,000


Sent from my iPad using Tapatalk HD

Cool, it's a huge improvement and never gets warm. Glad they took care of this for you

 

[unibob]

Fragtank side running with water, water just starting to fill display.

Will take some pics once area is cleaned up a bit.


Sent from my iPhone using Tapatalk

 

[unibob]

Sent from my iPhone using Tapatalk

 

[unibob]

Few minor leaks that need to be looked into, other then that, first 2 tanks in system are running, salinity is around 1.010 right now.


Sent from my iPhone using Tapatalk

 

[heath]

Looking good...

 

[Pistol]

The water flows. Adding rodi to fragtank side. Will add display into system once all plumbing arrives this week.

Sent from my iPhone using Tapatalk

Looking good buuuut, put a cover on that receptacle.

 

[EricTMah]

Sweet. I'll have to make a trip to see it when you're fully stocked

Sony Xperia Z3

 

[unibob]

Looking good...

Thanks, it's been a long time coming!

Looking good buuuut, put a cover on that receptacle.

there's one on it now. I moved it above everything too, so gravity is no longer a factor haha

Sweet. I'll have to make a trip to see it when you're fully stocked

Sony Xperia Z3

Thanks!


Sent from my iPhone using Tapatalk

 

[unibob]

I still need one 1.5" threaded elbow to finish display overflow, so if anyone local has one laying around...


Sent from my iPhone using Tapatalk

 

[teebone110]

I still need one 1.5" threaded elbow to finish display overflow, so if anyone local has one laying around...


Sent from my iPhone using Tapatalk

just make a quick stop at Plasco, and your good to go!
http://plascowelding.com

 

[unibob]

just make a quick stop at Plasco, and your good to go!
http://plascowelding.com

Aren't they east of Adelaide?


Sent from my iPhone using Tapatalk